Brightline B18 Hangar
Brightline Bags
5199
    Delivery time:3-5 Days
Add to cart
  • Description
  • More

A Flight Bag or Travel Bag that can handle all your gear. Adaptable by adding or removing center sections as needed.  Eight different bags can be built with the included modules.  Eight bags for the price of one.

Included Items:

  • Pocket Cap Front
  • CS2
  • CS5
  • CS11
  • Flat Cap Rear
  • Side Pocket Alpha
  • Side Pocket Bravo
  • Side Pocket Charlie
  • Side Pocket Delta
  • Main Handle
  • Shoulder Strap 

Size:

Interior of CS2: 13.0" tall, 10.0" wide, 2.0 inches deep. (34cm x 25cm x 7.6cm)
Interior of CS5: 13.0" tall, 10.0" wide, 5.0 inches deep. (34cm x 25cm x 10.2cm)
Interior of CS11: 13.0" tall, 10.0" wide, 11.0 inches deep. (34cm x 25cm x 28cm)

Exterior of entire bag: 14" tall, 13" wide, 22" deep. (36cm x 33cm x 56cm) (Including side pockets)

Keep in mind that the bag material is flexible, so the size of the interior storage may be able to "stretch" out just a bit in one direction or another. Also keep in mind that over-stuffing your bag can cause seam or material failure, and this is not covered by warranty.

Empty Weight:

9.8 lbs.  (4.47 kg)

Total Number of Available Flex System Side Pockets:

Six. (Two FLEX-Mount side pocket stations on the CS5, and four on the CS11.)

Modular Expansion Capability:

Unlimited. You can add any of the other FLEX System modules to this bag, in any order, to make a bag as big or as small as you need on any given day.
NOTE:  BOTH THE CS5 AND THE CS2 OPEN TO THE REAR.
Every module in the FLEX System has a front surface and a rear surface.  All of the modules are one-directional by necessity.  The original assumption was that the CS5 (or the CS2) would be added onto the back of a CS4 for more storage.  The CS4 opens to the front, and so therefore the CS5 and the CS2 open to the rear.  Thus, in the case of the B18, you should know that the PCF (Pocket Cap Front) will attach to the non-opening side of either the CS5 or CS2, and the FCR (Flat Cap Rear) will attach to the rear panel of the CS5 or CS2 which is the panel that opens and closes to give access to the contents of the CS5 and CS2. The Main Compartments of both the CS2 and CS11 have locking zipper sliders.  The Main Compartment of the CS5 DOES NOT YET HAVE locking zipper sliders. It will soon.

Embroidery Options:

The top front pocket cover of the POCKET CAP FRONT module can be removed to make it easy to add custom embroidery.
Also, the pocket on the very top of the CS11 can be removed in the same way to add embroidery. Just remove either of these pocket covers and hand them directly to your current embroidery provider.  (We don't offer any embroidery service.)

Description

Designed primarily for aviators who need a Pilot Flight Bag to pack multiple overnight items, such as clothes, shoes, coolers, etc., the B18 HANGAR fits the bill when maximum space is required. Also excellent for those in the Law Enforcement and Emergency Medical field.

The B18 is 13.5" x 10.5" x 22" with interior storage capacity of 18 inches. (And remember, it is a soft bag so it can expand slightly in every direction.)

The B18 HANGAR is comprised of the POCKET CAP FRONT, CENTER SECTION 5, CENTER SECTION 11, CENTER SECTION 2, FLAT CAP REAR, SIDE POCKET ALPHA (Large Radio/Water Bottle Pocket), SIDE POCKET BRAVO (Small Radio Pocket), SIDE POCKET CHARLIE (Pen Pocket), and SIDE POCKET DELTA (Double Pocket).  It also includes the MH and SS.  It does NOT include a SLIM HANDLE KIT.  If you ever think you'd like to remove the all of the Center Sections and zip just the two End Caps together to make the B0 SLIM, you'll need to make sure you also order an SLIM HANDLE KIT.

Storage on the B18 starts with the POCKET CAP FRONT: The POCKET CAP FRONT acts like the "hub" for your entire FLEX System. No matter which configuration you carry you'll be attaching the POCKET CAP FRONT to one end of your bag. And it's the "hub" because it holds all the important small stuff and tech stuff and personal stuff that you want with you no matter what. If you change configurations, you'll always move the POCKET CAP FRONT to the new configuration which means you'll always have all this key stuff with you, without any repacking or reloading.

PCF:   The POCKET CAP FRONT module offers a variety of pockets organized into three "main" pockets and six "secondary" pockets for a total of nine small pockets on the front panel. In these nine pockets you'll store all the cords, cables, chargers, batteries, stylus, memory cards, USB drives, etc, for all your electronic gear. All these important items will finally be separated and organized like you've always wanted. In addition, you'll have room for your flight timer, fuel testers, E6B, flashlights, compact portable GPS, etc. Not to mention space for your wallet, keys, cellphone, business cards, multi-tool, glasses, pens, markers, and things like Ibuprofen, Chapstick, bandaids, etc, and even your digital camera. There is also a flat half-height slip pocket on the inner surface of the module where you can stow an important document or two like a copy of your medical or your passport.

CS5:   Next, comes the CS5 (5-inch Center Section), which will commonly be used to hold anything from a bunch of flight documents, to a couple of changes of clothes, to your lunch.  The CS4 also comes with a divider shelf which serves to separate the compartment if necessary, which really comes in handy if you want to carry two more full-sized headsets.  You can instead fit 13” laptops and a small collection of documents.  Many, but not all, 14" laptops will also fit. - But no 15" laptops will fit. The CS5 has a really versatile dual-access feature. First, you get full top-access. You can unzip just the top of the bag to give access to your stuff right through the top of the bag. And then when you need, everything can also be accessed by unzipping the entire front panel all the way down to the bottom, giving access to the entire gray interior of the CS5. The Main Compartment of the CS5 DOES NOT YET HAVE locking zipper sliders. It will soon. On top of the bag is a pocket for sunglasses. The other key thing about the CS5 is that it has two FLEX-Mount Side Pocket stations, one on each side, for attaching the two included side pockets. You can, of course, also trade out the side pockets any time you like later on.

The CENTER SECTION 11 offers a full 11 inches of interior storage and swallows up multiple day's worth of clothes. In addition to clothes, the CS11 will carry a small cooler or helmet. The CS11 comes with two vertical divider shelves. If needed, you can organize a 13" laptop, documents, and clipboards.  The Main Compartment of the CS11 has locking zipper sliders. The top of the CS11 carries a 8 inches square pocket along with double side pocket mounting stations. The CS11 can be installed over the upright handles of our folding cart using the zipper access found on one side.

The CENTER SECTION 2 offers two inches of storage and easily carries 13" laptops, some 14" laptops, tablets as well as documents, folders, clipboards, etc.  The Main Compartment of the CS2 has locking zipper sliders.   NOTE: Many of the photos show a small one-inch webbing strap going across the very top of the module. This strap has been removed. It is no longer part of the bag.  We removed the strap because it was left over from the pre-FLEX days and it is no longer needed as a secondary handle. We just didn't want to go through all the trouble of reshooting all the photos just for this minor change.  We hope you understand.

The FLAT CAP REAR module offers two flat pockets on the outside, and one flat half-height slip pocket on the inner surface of the module. The primary outer pocket is accessed from the top and has a cover flap that is secured with Velcro. This where you'll likely store your iPad (as long as it's not in a thick case), or a manilla folder or two for some documents, or a magazine. There is a second flat panel that covers two-thirds of the outside of the main panel that is broken into two halves - an upper panel and a lower panel. By default, the bottom edge of the upper panel is "tucked" into the top edge of the lower panel.  This allows both panels to act together as a single slip pocket that works great for sticking a boarding pass or other simple paperwork here.  If the top panel is "untucked" from the bottom panel, this allows the telescoping tubes of a suitcase or folding cart to pass through and the panel serves to secure your bag to those tubes (especially when this FLAT CAP REAR is attached to other modules to form bigger bags like the B2 COMPUTE, B4 SWIFT or the B7 FLIGHT).  Then, when you're done putting your BrightLine Bag on top of your suitcase, you can just "tuck" the top panel back into the bottom panel and it becomes a slip pocket again.

Keep in mind that the modules included in the B18 can be assembled in any order.  You can also remove modules and reassemble the remaining modules into a smaller bag.  Or can combine other FLEX System modules.  Any FLEX System module can be zipped onto any other FLEX System module.

SIDE POCKET ALPHA is often called the "Radio Pocket".  It will hold any, repeat - ANY, handheld radio.  And the top flap is such that the antenna can just stick right out the side.  In addition, the SPA is great for holding a water bottle.  The front face of the pocket has an expansion zipper to allow bottles up to 20 ounces. To carry larger water bottles, please select a Side Pocket Echo instead.

SIDE POCKET BRAVO has two half-height compartments.  The upper compartment has a fold-over cover flap and it was originally designed for the short hand-held radios.  The lower compartment is closed with a zipper and it is great for holding small items like spare batteries or ear plugs, etc.

SIDE POCKET CHARLIE is often called the "Pen Pocket".  I has three pen slots on the outer surface plus a zippered pouch that has room for pens, marker, highlighter, spare reading glasses, etc.  Of course, many people will put completely different things in there besides pens. It's a great pocket many different purposes.

SIDE POCKET DELTA is a "double-wide" pocket which mounts on two adjacent FLEX-mount side pocket stations.  The two mounting stations can be found either on a CS11, or they can even be found on two adjacent modules and the Side Pocket Delta can bridge across the gap between the two modules. 

The B18 HANGAR comes with a MAIN HANDLE and a SHOULDER STRAP.

 

 

INCLUDED MODULES:
POCKET CAP FRONT
CENTER SECTION 2
CENTER SECTION 5
CENTER SECTION 11
FLAT CAP REAR
Side Pocket Alpha
Side Pocket Bravo
Side Pocket Charlie
Side Pocket Delta 
 
INCLUDED ITEMS:
Main Handle
Shoulder Strap
Slim Handle Kit
Slim Handle
Adapter Loop (qty 2)
D3 Clip (qty 4)
Instruction sheets
 
SIZE:
Interior of CS2: 13.5" tall, 10.0" wide, 2.0 inches deep. (34cm x 25cm x 7.6cm)
Interior of CS5: 13.5" tall, 10.0" wide, 5.0 inches deep. (34cm x 25cm x 10.2cm)
Interior of CS5: 13.5" tall, 10.0" wide, 11.0 inches deep. (34cm x 25cm x 28cm)
Exterior of entire bag: 14" tall, 13" wide, 22" deep. (36cm x 33cm x 56cm) (Including side pockets)
Keep in mind that the bag material is flexible, so the size of the interior storage may be able to "stretch" out just a bit in one direction or another. Also keep in mind that over-stuffing your bag can cause seam or material failure, and this is not covered by warranty.
 
EMPTY WEIGHT:
11.5 lbs. (5.2 kg)
 
TOTAL NUMBER OF POCKETS AND STORAGE COMPARTMENTS:
39
 
TOTAL NUMBER OF AVAILABLE FLEX SYSTEM SIDE POCKETS:
Six. (One FLEX-Mount side pocket station on the CS5, and four on the CS11.)
 
TOTAL VOLUMETRIC STORAGE:
Inside the CS2 = 270 cubic inches. (4,420 cubic cm)
Inside the CS5 = 675 cubic inches. (11,060 cubic cm)
Inside the CS5 = 1,485 cubic inches. (22,300 cubic cm)
(And, of course, the four narrow spaces between the five modules can accommodate some small amount of flat stuff)
 
MODULAR EXPANSION CAPABILITY:
Unlimited.  You can add any of the other FLEX System modules to this bag, in ay order, to make a bag as big or as small as you need on any given day.
 
EMBROIDERY OPTIONS:
The top front pocket cover of the POCKET CAP FRONT module can be removed to make it easy to add custom embroidery.
Also, the pocket on the very top of the CS11 can be removed in the same way to add embroidery.


• DESCRIPTION •
 
Designed primarily for aviators who need a Pilot Flight Bag to pack multiple overnight items, such as clothes, shoes, coolers, etc., the B18 HANGAR fits the bill when maximum space is required. Also excellent for those in the Law Enforcement and Emergency Medical field.

The B18 is 13.5" x 10.5" x 22" with interior storage capacity of 18 inches. (And remember, it is a soft bag so it can expand slightly in every direction.)

The B18 HANGAR is comprised of the POCKET CAP FRONT, CENTER SECTION 5, CENTER SECTION 11, CENTER SECTION 2, FLAT CAP REAR, SIDE POCKET ALPHA (Large Radio/Water Bottle Pocket), SIDE POCKET BRAVO (Small Radio Pocket), SIDE POCKET CHARLIE (Pen Pocket), and SIDE POCKET DELTA (Double Pocket).

The POCKET CAP FRONT offers a variety of pockets organized into three Main Pockets and six auxiliary pockets. The top Main Pocket area is designed to hold your mobile device, wallet and keys. The middle and lower pockets can store your electronic E6B, camera, business cards, iPods, chargers, batteries, etc. The auxiliary pockets are perfect for storing flashlights, fuel testers, and multi-purpose tool.

The CENTER SECTION 5 offers five inches of storage space and comes with a divider shelf attaching to the side walls of the main compartment with Velcro. This shelf can be positioned right where you need it or removed for full access storing one or two headsets or GPS. Access is through a unique top zipper design that also opens the entire length allowing you to reach all the items above and below the divider shelf. On top of the bag is a pocket for sunglasses. There are two FLEX Mount Pocket stations on both sides of the CENTER SECTION 5.

The CENTER SECTION 11 offers a full 11 inches of interior storage and swallows up multiple day's worth of clothes. In addition to clothes, the CS11 will carry a small cooler or helmet. The CS11 comes with two vertical divider shelves. If needed, you can organize a 13" laptop, documents, and clipboards. The top of the CS11 carries a 8 inches square pocket along with double side pocket mounting stations. The CS11 can be installed over the upright handles of our folding cart using the zipper access found on one side.

The CENTER SECTION 2 offers two inches of storage and easily carries 13" laptops, some 14" laptops, tablets as well as documents, folders, clipboards, etc.

The FLAT CAP REAR offers two flat pockets on the outside. The primary pocket is accessed from the top and has a cover flap that is secured with Velcro. There is a second flat half-height slip pocket that acts as a great place to store a couple of basic documents that you want to have easy access to such as today's checklists or your boarding pass. This half-height pocket offers a zipper across the bottom opening 9 inches to allow it to slip over the upright handle of your folding cart or rolling suitcase.
 
SIDE POCKET ALPHA is often called the "Radio Pocket".  It will hold any, repeat - ANY, handheld radio.  And the top flap is such that the antenna can just stick right out the side.  In addition, the SPA is great for holding a water bottle.  The front face of the pocket has an expansion zipper, so the pocket can hold larger or smaller water bottles.  It will hold up to a 20 oz bottle.
 
SIDE POCKET BRAVO has two half-height compartments.  The upper compartment has a fold-over cover flap and it was originally designed for the short hand-held radios.  The lower compartment is closed with a zipper and it is great for holding small items like spare batteries or ear plugs, etc.
 
SIDE POCKET CHARLIE is often called the "Pen Pocket".  I has three pen slots on the outer surface plus a zippered pouch that has room for pens, marker, highlighter, spare reading glasses, etc.  Of course, many people will put completely different things in there besides pens. It's a great pocket many different purposes.
 
SIDE POCKET DELTA is a "double-wide" pocket which mounts on two adjacent FLEX-mount side pocket stations.  The two mounting stations can be found either on a CS11, or they can even be found on two adjacent modules and the Side Pocket Delta can bridge across the gap between the two modules. 
 
The B18 HANGAR (as well as the other four standard pre-configured bags) comes with a MAIN HANDLE (the B0 needs no Main Handle), a SHOULDER STRAP, and also a SLIM HANDLE KIT. The SLIM HANDLE KIT consists of a SLIM HANDLE, two ADAPTER LOOPS, and four D3 CLIPS. The MAIN HANDLE or the SHOULDER STRAP can be attached to the CS4 by use of the quick release clips. If you convert the B18 to a B0 by removing all three Center Sections, then the D3 CLIPS and the ADAPTER LOOPS can be installed so that you can use BOTH the SLIM HANDLE and the SHOULDER STRAP at the same time with the B0. Note: If you try to carry the entire B18 HANGAR with the SLIM HANDLE KIT, the D3 CLIPS will fail and you may drop the bag and risk damaging the entire contents.